top of page
uMake Online Factory Instant Laser Cutting Canada

Custom wood and plastic parts, CNC-manufactured in Quebec

Free Shipping Canada
orders over $250 excluding oversize parcels. please see details. 

Check the scale.

Check the units of measurement.

Ensure a gap of at least 5 mm between each cut-out.

Leave a 20 mm margin around the edges; do not use the edge of the material as a boundary.

Check the material thickness; ensure that no cut-out feature is smaller than the thickness of your material.

Ensure there are no overlapping or double lines, and that all shapes are defined as outlines (paths).

You may send us all your sheets in a single file, or group the parts to be cut by material thickness.

If you wish to include engravings or pockets, please indicate them using different colors.

​

Custom wood and plastic parts, CNC-machined in Quebec.

uMake.ca - Online Factory CNC Bois Quebec

Internal shapes to consider: Dogbones

CNC design guidelines

Parts up to 140" x 61"

CNC Inside Corner Radius uMake Canada

It is important to note that internal corners may have a slight radius due to the round cutting tool used. This radius will be equal to half the tool's diameter; for example, if a 3 mm milling cutter is used, the internal radius will be 1.5 mm.

While external corners remain unaffected, you can adjust an internal radius by filing the corners. However, opting for a smaller milling cutter to achieve a smaller radius is often the most effective solution, provided your design allows for it.

CNC Dogbone uMake.ca Canada

"Dogbones" are an essential technique in CNC cutting, used to mitigate the issue of rounded internal corners caused by milling bits. By incorporating these specially shaped cutouts—known as dogbones—you can achieve sharper corners and enhance the overall appearance of your project. For instance, using 1/8-inch bits creates a specific style of dogbone (shown on the left), while using 1/4-inch bits produces a more pronounced effect (shown on the right). You can also opt for less prominent dogbones for a more subtle look, as illustrated in the second image.

CNC Router Table Layout Quebec Canada uMake.ca
CNC Dogbones fillets uMake.ca Montreal Canada

Dog-bone fillets are used to reduce sharp edges at angles/corners.

CNC Technical Design Tools

If you do not use "dog-bone" fillets, your cut will have an internal radius of 1.576 mm when using a 3.175 mm (1/8") bit, or 3.175 mm when using a 6.35 mm (1/4") bit. In this case, you will need to make manual corrections by filing the material by hand or by using a softer, sacrificial material such as OSB.

MAXIMUM SIZE 61"x140"

MDF     49"x97"
           61"x121"

Technical CNC Instruction for dogbones uMake

It is also possible to add a hole in the corner, but this amounts to an unnecessary, large "dog bone" shape being added.

Technical CNC Instruction for dogbones uMake Canada

If you position your "dog bone" (connector) so that it is the minimum necessary size, you will end up with a gap of only about 0.5 mm, which is quite subtle.

Technical CNC Instruction for dogbones uMake Montreal

You can also reach a compromise by accepting a very small corner, as indicated for various bit sizes.

Plywood  48"x96"
               60"x60"
               60"x120"

Tabs

CNC Manufacturing recommendations uMake.ca Montreal Canada

When using our CNC router, you will notice small attachment tabs along the edges of your components. These tabs, which are approximately 0.1875 inches wide, play a crucial role in securing your parts throughout the manufacturing process.

For an optimal cut, we recommend maintaining a minimum spacing of 0.400 inches between these tabs (or anchor points). The depth of each tab—equal to half the thickness of the chosen material—can be easily sanded away without affecting your design, ensuring both precision and stability during the cutting process.

FAQ

Technology, Capabilities & Design for CNC Routers in Quebec

Q1 What is a CNC router, and how does it differ from a laser or waterjet cutter? A CNC router is a computer-controlled milling machine that uses a rotating cutting tool (end mill) to cut, pocket, engrave, and carve non-metallic materials such as wood, plastics, composites, and foams. Unlike a CO₂ laser, which burns material using a light beam, or a waterjet, which erodes material through abrasion, a CNC router removes material mechanically. This enables deep-cutting operations—such as pockets, grooves, 3D profiles, and raised textures—that are not possible with the other two processes. It is the preferred choice for designers, cabinetmakers, architects, and signage manufacturers in Quebec who require complex shapes in large-format materials.

Q2 What materials can be machined on the CNC router at uMake in Quebec? Our CNC router processes a wide range of non-metallic materials: Wood & panels: Baltic Birch plywood (sizes: 48"×96", 60"×60", 60"×120") MDF (sizes: 49"×97", 61"×121") Masonite, particle board, OSB, rigid cardboard Engineering plastics: Acrylic (clear, colored, tinted) Polycarbonate PVC (white and black Sintra) HDPE, ABS, Delrin (Acetal), Nylon, UHMW Composites & specialty materials: Dibond® (aluminum composite) Rigid foam board Corian, HPL laminates For acrylic, we use diamond-polishing bits to achieve optically clear edges. For plywood, we use compression bits to ensure a clean surface on both sides of the sheet. Each material is matched with the optimal tool—never a "one-size-fits-all" bit.

Q3 What is the maximum size of parts you can machine using a CNC router in Quebec? Our CNC router table accommodates panels up to 140" × 61" (approximately 355 cm × 155 cm). This is one of the largest capacities available in Quebec for online orders. Specific dimensions based on material type are as follows: MDF: 49" × 97" or 61" × 121" Baltic Birch Plywood: 48" × 96", 60" × 60", or 60" × 120" Plastics (acrylic, PVC, polycarbonate): up to 61" × 140", subject to availability For projects that exceed these dimensions, we can produce assembled parts with precise joints. Please contact quoting@umake.ca for projects that fall outside these standard dimensions.

Q4 What is the maximum thickness that the CNC router at uMake can process? Our CNC router can process materials up to 3 inches (76 mm) thick for through-cuts, and even thicker for pocketing or partial-depth engraving operations. In practice, the maximum cutting depth per pass depends on the material and the diameter of the cutting tool. For thick sheets of engineering plastic or solid wood, we adjust the cutting strategy (using multiple passes) to ensure clean edges and precise tolerances. Please specify the exact thickness of your material when placing your order at app.umake.ca—our system will automatically incorporate this into the quote calculation.

Q5 What is a "dogbone" in CNC machining, and why is it important for your file? This is one of the most critical questions to consider when preparing a file for CNC machining. Because a milling bit is round, it cannot create a perfect 90° internal corner—it always leaves behind a small radius equal to half the bit's diameter. For example: 1/8" (3.175 mm) bit → residual internal radius of 1.576 mm 1/4" (6.35 mm) bit → residual internal radius of 3.175 mm The "dogbone" technique involves adding a small circular cutout to each internal corner of your geometry, allowing the milling bit to reach fully into the corner and produce a functionally square angle. This is essential for interlocking assemblies (such as boxes, furniture, or mortise-and-tenon structures) where parts must fit together precisely. Without a dogbone, you would have to manually correct the corners using a file—otherwise, the parts simply will not fit together properly.

Q6 Do I need to add the dogbones to my file myself, or does uMake handle that? For most standard orders, you must include the dogbones in your file before submitting it. This is your responsibility as the designer, as only you know the appropriate bit size for your application and how subtle you want the dogbones to be (some clients prefer minimalist, barely visible 0.5 mm dogbones). If you are unsure about which bit size will be used, or if your project is complex, please email quoting@umake.ca—our technical team can advise you on the optimal cutting strategy before production begins.

Q7 What are CNC tabs and how do I manage them after cutting? During CNC machining, the cut parts risk moving due to the vibrations of the cutter, especially towards the end of the cut when they are only holding a few millimeters of material. To avoid this, our system automatically adds small attachment tabs (approximately 0.1875" wide) that hold your parts secure to the plate during manufacturing. These tabs are approximately half the thickness of the material and are easily removed with a handsaw or file after delivery — they do not affect your final dimensions. For best results, keep a minimum spacing of 0.400" between anchor points in your drawing.

Q8 What dimensional tolerances can uMake’s CNC router achieve? uMake regularly calibrates its CNC machines to maintain consistent dimensional accuracy. Typical tolerances for CNC routing range from ±0.1 to ±0.25 mm, depending on the material and geometry. For projects where the exact material thickness is a critical variable in your assembly—such as with mortise-and-tenon joinery—we provide the actual thickness of the stock on hand prior to production, allowing you to adjust your tolerances if necessary. This transparency helps avoid unpleasant surprises during assembly and reduces the need for on-site rework.

Q9 Can the CNC router perform engraving and pocketing, or is it limited to through-cutting? The CNC router at uMake can perform several types of operations in addition to through-cutting: Surface engraving: tracing lines, logos, text, or patterns at a partial depth without cutting all the way through the material. Pocketing: milling out flat areas to a controlled depth—ideal for inlays, cavities, interlocking parts, or creating relief effects. 3D profiling: on certain materials, creating curved surfaces or relief shapes through successive passes. To specify engraving and pocketing operations in your file, use different colors for each type of operation (for example: red for through-cutting, blue for a 5 mm pocket, and green for surface engraving). Our quoting platform recognizes these conventions and incorporates them into the price calculation.

Q10 What kind of cut quality can I expect for acrylic and Baltic Birch plywood at uMake? The cut quality varies depending on the material and the tools used: Acrylic: uMake uses diamond-polished router bits specifically designed for transparent plastics. The result is an optically clear, near-polished edge, free of burrs or burn marks—ready for assembly or display without any additional sanding. This is particularly important for retail displays, backlit signs, and decorative pieces. Baltic Birch Plywood: uMake uses compression bits that cut both downward and upward simultaneously, producing a clean edge on both sides of the panel without fraying or surface splintering. This is ideal for furniture, jigs, and visible structural components.

Orders, Deadlines, Files, and Applications in Quebec

Q11 How can I get an instant quote for CNC router parts in Quebec? Visit app.umake.ca and upload your DXF, AI, SVG, or vector PDF file. The platform automatically analyzes your geometries—detecting cutting contours, pockets, and engravings—and generates an instant quote, including pricing, production lead time, and shipping options, with no need to wait for a representative. You can select your material, thickness, and quantity in real time. For projects involving 3D geometries, specialized materials, or multi-part assemblies, please send your files to quoting@umake.ca to receive a custom estimate.

Q12 What file formats should I submit for a CNC router order in Quebec? uMake accepts the following formats for CNC routing: DXF — a universal format recommended for all 2D geometries, dimensions, and pockets AI (Adobe Illustrator) — ideal for logos, typography, signage, and decorative patterns SVG — accepted for all 2D shapes Vector PDF — accepted (vector files only; no raster/pixel-based images) DWG — native AutoCAD format Essential file preparation guidelines: Verify the scale and units of measurement (mm or inches) Leave at least 5 mm of space between each part Maintain a 20 mm margin around the perimeter—do not use the edge of the material as a boundary Ensure that no part is smaller than the thickness of your material Remove any overlapping or duplicate lines—all contours must be closed Use different colors to distinguish between through-cuts, pockets, and engravings Add "dogbones" (relief cuts) to internal corners before submission

Q13 Is there a minimum order requirement for CNC routing services in Quebec with uMake? No. uMake.ca does not impose any minimum quantity or minimum order value for CNC routing. You can order a single piece—a one-off panel prototype, a custom jig, or an individual furniture component—and receive the same professional service and quality as you would for a production run of 500 units. This flexibility is especially valued by woodworkers, interior designers, artists, and makers in Quebec who are working on unique projects or are in the concept-validation phase.

Q14 What are the production and delivery lead times for CNC parts in Quebec? For materials in stock (MDF, Baltic Birch, clear acrylic, white/black PVC, polycarbonate), typical lead times are: Manufacturing: 1 to 2 business days for orders requiring less than one hour of machine time Delivery within Quebec: 1 to 3 business days after shipment from Montreal Typical combined lead time: 3 to 4 business days, door-to-door, for most regions in Quebec Delivery is free for all orders over $250 (excluding oversized packages). uMake operates more than 15 machines simultaneously, ensuring high manufacturing capacity even during periods of high demand. For ultra-urgent (24-hour) turnaround, please contact quoting@umake.ca directly.

Q15 Can I provide my own material for CNC routing at uMake in Quebec? Yes. uMake accepts customer-supplied material for CNC routing. Your material must be flat, uniform in thickness, and compatible with rotary-bit machining. The maximum dimensions are 61" × 140". Providing your own material can be advantageous for projects involving heritage materials, specialty laminates, certified panels, or materials not currently in our stock. Please contact our team at quoting@umake.ca before sending any material to confirm compatibility and avoid any unexpected issues.

Q16 For which applications is CNC routing most commonly used in Quebec? uMake’s clients in Quebec primarily use CNC routing for: Furniture & Interior Design: Kitchen and bathroom cabinetry, custom shelving, tables, chairs, beds, carved headboards, decorative room dividers, and wall paneling made from MDF or plywood. Signage & Displays: Acrylic business signs, cut-out PVC (Sintra) lettering, acrylic point-of-sale displays, routed directional signage, and dimensional lettering. Architecture & Construction: Decorative cladding panels (MDF or Dibond), architectural screens, carved wall paneling, decorative grilles, and light boxes. Set Design & Events: Film and television props, theatrical sets, exhibition installations, pop-up structures, and decor for weddings and events. Prototyping & Industry: Production templates, assembly jigs, architectural models, product prototypes, and electronic enclosures made from acrylic or polycarbonate. Art & Installations: CNC-carved wooden sculptures, plywood wall art, geometric mosaics, and light installations featuring backlit acrylic.

Q17 What is the difference between a CNC router and CO₂ laser cutting for wood and plastic in Quebec? Both processes can cut wood and plastic, but they are not interchangeable for every application: CNC Router | CO₂ Laser Maximum thickness: 3 inches | ¼ inch Pockets & 3D milling: ✅ Yes | ❌ No Acrylic cutting: Matte polished edge | Glossy, fused polished edge Speed ​​on large parts: Faster | Slower Fine engraving & text: Less precise | Highly precise Thick materials: Ideal | Not applicable Maximum envelope: 61" × 140" | 60" × 60" A rule of thumb for clients in Quebec: if your part is thick (more than ¼") or requires pockets or a 3D profile, choose a CNC router. If your part is thin or requires very fine engraving or a glossy, fused edge (for example, for backlit acrylic), a CO₂ laser is preferable. Our quoting platform can suggest the optimal process based on your file.

Q18 Can uMake combine CNC routing with other processes for my project in Quebec? Absolutely—in fact, this is one of the key advantages of uMake.ca, a full-service production facility located in Montreal. Common combinations for our clients in Quebec include: CNC routing + CO₂ laser: MDF panels cut via CNC, featuring fine laser-engraved text or logos. CNC routing + UV printing: Acrylic or PVC parts that are CNC-cut and then printed directly on the surface using CMYK+white ink. CNC routing + fiber laser: Wooden structures produced via CNC, incorporating metal inserts cut with a fiber laser. CNC routing + metal bending: Hybrid wood-and-metal furniture, or enclosures featuring a CNC-machined structure with bent aluminum door panels. This integrated approach eliminates the need to manage multiple vendors, shortens coordination timelines, and ensures dimensional consistency across all parts manufactured under one roof.

Q19 Is uMake a good choice for woodworkers and cabinetmakers in Quebec who need CNC subcontracting services? Yes—many woodworkers and cabinetmakers across the province rely on uMake.ca as a CNC subcontracting partner for projects that exceed the capabilities of their own equipment, or to help shorten their turnaround times. uMake can handle complex panel cutting, non-standard shapes, pocket milling, and repetitive production runs—tasks that some workshops cannot perform using only a table saw or a handheld router. With no minimum order requirements, an instant online quoting system, and fast delivery throughout Quebec, uMake’s subcontracting services integrate seamlessly into any woodworking shop’s workflow.

Q20 Where is the uMake facility located, and can I visit as a client from Quebec? The uMake.ca facility is located at 8487, 8th Avenue, Montreal, QC H1Z 2X2—approximately a 2-hour and 45-minute drive from Quebec City. We welcome clients from across the province who wish to tour our facilities, inspect parts currently in production, or discuss a project in person with our bilingual (French/English) technical team. If you are planning a visit, please reach out beforehand at +1 514 524 9990 or via email at quoting@umake.ca to ensure our team is available. For the vast majority of projects, our online platform and email correspondence are more than sufficient—but our doors remain open.

bottom of page